iP60-80DS Diesel Waterjet Pump

55,000 psi (3800 bar) Continuous Operating Pressure
80 hp, 1.3 gpm (4.9 lpm) Maximum Flow Rate


Built with the waterjet contractor in mind, Jet Edge's diesel-powered waterjet intensifier pumps are built for years of dependable service in harsh and remote environments.

Experienced waterjet contractors prefer Jet Edge hydraulic waterjet intensifier pumps.

Here’s why:

  • Reliable Tie-Rod Design eliminates threads on the high pressure cylinders, end caps, and hydraulic cylinders. This reduces the likelihood of cracking and increases component life.

  • Reliable Cummins turbo diesel engines - Tier 3 certified.

  • Matched metal components prevent galling of hydraulic components. Intensifier designs allow for the usage of common tools instead of specialized jacking system tools. Hydraulic accumulators are standard on all pumps. This provides smoother hydraulic pressure, reduces spikes and prolongs hydraulic pump life.

  • Hydraulic fluid is cooled and filtered.

  • Rugged hydraulic center section incorporates high duty cycle-rated piston seal and wear rings.

  • Easy Maintenance - Intensifier components can be accessed without having to get into the hydraulic center section and hydraulic rod seal.

  • Leak detection block indicates seals needing replacement. (optional on some pumps).

  • No special tools required.

  • CE-marked attenuator smoothes pressure fluctuations and delivers constant and steady stream of UHP water.

  • On-board water filtration protects pump components, maximizing machine run time.

  • Ambient temperature: 50-100ºF (10-37º C)
  • Relative humidity: Non condensing, maximum 95% at 100ºF (38ºC)
  • Engine output: 80 hp
  • Engine type: Cummins 4 cylinder turbocharged diesel (meets Tier 3 emission standard)
  • Fuel Tank: 27 U.S. gal (100 L)
  • Cooling: Air cooled circulating water (radiator)
Low Pressure Water
  • Type (recommended): Potable tap water
    *Pretreated, <100 TDS, PH 6-8, Silica <15PPM
  • Input Pressure: Minimum pressure 40 psi (3 bar) at 7 gpm (26 lpm)
  • Input temperature: Maximum temperature 70ºF (21ºC)
  • Filtration: Two filters, 10 micron and 1 micron
High Pressure Water
  • Output Pressure: 55,000 psi (3800 bar) continuous
  • Flow rate: 1.3 gpm (4.9 L/m)
  • Pump type: Axial piston, variable displacement, pressure compensated
  • Pressure rating: 3,200 psi (220 bar)
  • Cooling: Air over oil heat exchanger
  • Filtration: 10 micron kidney loop; 13 gpm at 1800 rpm (49 L/m)
  • Fluid capacity: 35 U.S. gallons (135 L)
  • Fluid type: Standard: medium grade turbine ISO
Physical size
  • Length: 88 inches (2240 mm)
  • Width: 64 inches (1630 mm)
  • Height: 65 inches (1650 mm)
  • Weight: 3,500 lb (1590 kg) dry

Specifications subject to change.


Jet Edge is one of the few waterjet manufacturers willing to custom engineer solutions so you receive a system manufactured to satisfy your specific requirements. Our willingness to customize has made us the go-to waterjet supplier for solving the world’s toughest waterjet problems.

Call us today to discuss a custom solution for your manufacturing challenge!

1-800-JET-EDGE | 763-497-8700

Every Jet Edge system includes unlimited lifetime hands-on training at Jet Edge’s state-of-the art training lab. Training is free when taken at Jet Edge’s headquarters. You also can arrange to have training at your facility for a fee.
Training for Jet Edge's mobile equipment line is being scheduled by request only. To request a class, please call 763-497-8700, Ext. 744
You must be a Jet Edge customer to be eligible for training.
Safe-Cut Provides Safe, Efficient Waterjet Cutting Services to Refinery Industry