IP60-30 Waterjet Pump

The iP60-30 features electronically shifted intensifiers and a 1 quart (.9 liter) high pressure attenuator.
 

A closer look at the pump.

Designed for shops that desire the reliability of a hydraulic intensifier pump, but have limited power, the iP60-30 draws only 37 full load amps at 460vac (60Hz) or 74 full load amps at 230vac (60Hz).  It is capable of producing 0.6 gpm (2.3 L/m) of UHP water at a continuous operating pressure of 55,000 psi (3800 bar).
 
Like all Jet Edge intensifier pumps, the iP60-30 features a reliable tie-rod design that eliminates threads on the high pressure cylinders, end caps, and hydraulic cylinders. This reduces the likelihood of cracking and increases component life. Matched metal components prevent galling of hydraulic components. The iP60-30 includes a hydraulic accumulator to provide smoother hydraulic pressure, reduce spikes and prolong hydraulic pump life.
A CUT ABOVE

Experienced waterjet shops prefer Jet Edge hydraulic waterjet intensifier pumps.

Here’s why:

  • Reliable Tie-Rod Design eliminates threads on the high pressure cylinders, end caps, and hydraulic cylinders. This reduces the likelihood of cracking and increases component life.

  • Matched metal components prevent galling of hydraulic components. Intensifier designs allow for the usage of common tools instead of specialized jacking system tools. Hydraulic accumulators are standard on all pumps. This provides smoother hydraulic pressure, reduces spikes and prolongs hydraulic pump life.

  • Hydraulic fluid is cooled and filtered.

  • Rugged hydraulic center section incorporates high duty cycle-rated piston seal and wear rings.

  • Easy Maintenance - Intensifier components can be accessed without having to get into the hydraulic center section and hydraulic rod seal.

  • Leak detection block indicates seals needing replacement. (optional on some pumps).

  • No special tools required.

  • CE-marked attenuator smoothes pressure fluctuations and delivers constant and steady stream of UHP water.

  • On-board water filtration protects pump components, maximizing machine run time.

  • Standard Wye-Delta motor starter –Extends the life of the high-efficiency motor and minimizes installation costs.

  • Easy Operation - Jet Edge pumps can be controlled remotely from the motion controller and have programmable dual pressures.

PRODUCT SPECIFICATIONS
Construction
 
  • Rugged all-steel welded framework
  • Integral hydraulic reservoir
  • NEMA 12/13 rated electrical enclosure
Standard Features
 
  • High-efficiency TEFC motor
  • 1500 or 1800 nominal motor speed (rpm)
  • Electronically shifted intensifiers
  • Wye-Delta soft start with disconnect
  • 1 quart (.9 liter) high pressure attenuator
  • Safety shutdown systems
  • Automatic safety pressure bleed-down valve
  • Thermostatically controlled cooling system
  • Programmable Logic Controller (PLC) for operation and safety monitoring
  • Axial piston, variable displacement, pressure-compensated hydraulic pump
  • Liquid-filled pressure gauges
  • UHP safety shielded tubing
  • U/L, CU/L listed industrial control panel
  • Kidney loop cooling circuit
Optional Features
 
  • Removable heavy gauge sheet metal covers
  • CE Mark
Physical Size
 
  • Length: 61 in (1550 mm)
  • Width: 41 in (1040 mm)
  • Height: 38 in (965 mm)
  • Approximate Weight with Fluid: 1600 lb (726 kg)
Electric Motor
 
  • Motor Output: 30 hp (22 kw)
  • Motor Type: High Efficiency TEFC electric motor
  • Full load current: 37 amps @ 460vac, 74 amps @ 230vac
Intensifier
 
  • Type: Single piston, dual plunger, reciprocating
  • Number of Intensifiers: one
  • Continuous operating pressure: 55,000 psi (3800 bar)
  • Intensification Ratio: 20:1
  • Flow Rate: 0.6 gpm (2.3 L/m)
Low-Pressure Water/Intensication Water
 
  • Type: Pretreated, <100 TDS, PH 6-8, Silica <15PPM
  • Supply Requirements: Flow: 1.2 gpm (4.5 lpm) @ 60 psi (4.1 bar)
  • Temperature: 70F (21C) maximum
  • Filtration to 45 Micron
  • 2 Gallon Accumulator
Coolant Water
 
  • Maximum Temperature: 70°F (21°C)
  • Minimum: Flow: 3 gpm (11.4 lpm) @ 70F (lower flow if water supply is lower temperature)
  • Heat Exchanger: Stainless Steel Brazed Plate
  • Heat Load: 20,000 BTUs/Hour
Hydraulics
 
  • Reservoir Capacity: 20 gal (75 L)
  • Filtration: Full Flow 10 Micron
  • Cooling: 10 GPM @ 60Hz (8.5 GPM @ 50 Hz)
Environmental
 
  • Ambient Room Temperature: 50°-100°F (10°-37°C)
  • Relative Humidity: Noncondensing, Maximum 95% @ 100°F
 
Specifications subject to change.
 
CUSTOM SOLUTIONS

Jet Edge is one of the few waterjet manufacturers willing to custom engineer solutions so you receive a system manufactured to satisfy your specific requirements. Our willingness to customize has made us the go-to waterjet supplier for solving the world’s toughest waterjet problems.

Call us today to discuss a custom solution for your manufacturing challenge!


1-800-JET-EDGE | +1 763-497-8700

LIFETIME TRAINING

Every Jet Edge system includes unlimited lifetime hands-on training at Jet Edge’s state-of-the art training lab. Training is free when taken at Jet Edge’s headquarters. You also can arrange to have training at your facility for a fee.

Register for classes online or call 1-800-JET-EDGE (538-3343) or +1 763-497-8700 to schedule custom training sessions for your business.

You must be a Jet Edge customer to be eligible for training.

Have questions? Contact Us

1-800-JET-EDGE (538-3343)

+ 1 763-497-8700

E-mail our Sales Team

 

Request More Information
PDF Product Specifications
Watch Video