iP36-100 Waterjet Intensifier Pump

The iP36-100 features Jet Edge's reliable tie-rod design and attenuator to smooth pressure fluctuations.

The iP36-100 intensifier pump features a 100hp electric motor.

5,000 to 36,000 psi (345 to 2,800 bar) Adjustable Output
100 hp, 3.5 gallons (13.21 liters) Maximum Flow Rate


Experienced water jet shops and contractors prefer Jet Edge's iP36-100 hydraulic intensifer pump for UHP blasting and waterjet cutting applicatons.

Here’s why:
  • Reliable Tie-Rod Design eliminates threads on the high pressure cylinders, end caps, and hydraulic cylinders. This reduces the likelihood of cracking and increases component life.

  • Skid-mounted frame with lifting eyes and forklift guides make it easy to move and position.

  • Output pressure can be adjusted between 5,000 to 36,000 psi (345 to 2800 bar).

  • Matched metal components prevent galling of hydraulic components. Intensifier designs allow for the usage of common tools instead of specialized jacking system tools. Hydraulic accumulators are standard on all pumps. This provides smoother hydraulic pressure, reduces spikes and prolongs hydraulic pump life.

  • Hydraulic fluid is cooled and filtered.

  • Rugged hydraulic center section incorporates high duty cycle-rated piston seal and wear rings.

  • Easy Maintenance - Access panels make it easy to maintain the pump. Intensifier components can be accessed without having to get into the hydraulic center section and hydraulic rod seal.

  • Leak detection block indicates seals needing replacement. (optional on some pumps).

  • No special tools required.

  • CE-marked attenuator smoothes pressure fluctuations and delivers constant and steady stream of UHP water.

  • On-board water filtration protects pump components, maximizing machine run time.

  • Standard Wye-Delta motor starter –Extends the life of the high-efficiency motor and minimizes installation costs.

  • Easy Operation - Jet Edge pumps can be controlled remotely from the motion controller and have programmable dual pressures.

Physical Size
  • Length: 96 in (224 cm)
  • Width: 37 in (94 cm)
  • Height: 60 in (152 cm)
  • Approximate weight with fluid: 4,600 lbs (2,090 kg)
Electric Motor
  • Motor output: 100 hp (75 kw)
  • Motor type: High efficiency TEFC electric motor
  • Full load amps @ 460 VAC (60 Hz) 124
  • Full load amps @ 230 VAC (60 Hz) 248
  • Full load amps @ 380 VAC (50 Hz) 147
  • Type: Single piston, dual plunger, reciprocating
  • Number of intensifiers: 2
  • Continuous output pressure: 36,000 psi (2,500 bar)
  • Intensification ratio: 12:1
  • UHP flow rate: 3.5 gpm (13.21 lpm)
Low-Pressure Water
  • Type potable tap water, *pretreated, <100 TDS, PH 6-8, Silica <15 PPM
  • Supply requirements: 40 psi
  • Filtration: On board, 1 micron
Coolant Water
  • Maximum temperature: 70° F (21° C)
  • Minimum supply: 4 gpm (15.1 L/min), 40 psi minimum
  • Heat Load: 80,000 BTU’s /HR
  • Reservoir Capacity: 104 gal (394 L)
  • Filtration: Full Flow 10 Micron
  • Ambient Room Temperature 50° -100°F (10° -37°C)
  • Relative Humidity Noncondensing, Maximum 95% @ 100°F
Optional CE Mark Available

Jet Edge is one of the few waterjet manufacturers willing to custom engineer solutions so you receive a system manufactured to satisfy your specific requirements. Our willingness to customize has made us the go-to waterjet supplier for solving the world’s toughest waterjet problems.

Call us today to discuss a custom solution for your manufacturing challenge!
1-800-JET-EDGE | 763-497-8700


Every Jet Edge system includes unlimited lifetime hands-on training at Jet Edge’s state-of-the art training lab. Training is free when taken at Jet Edge’s headquarters. You also can arrange to have training at your facility for a fee.

Register for classes online or call 1-800-JET-EDGE (538-3343) or +1 763-497-8700 to schedule custom training sessions for your business.

You must be a Jet Edge customer to be eligible for training.