iP60-150 Waterjet Intensifier Pump

Jet Edge waterjet pumps are built to last. This counter is from a customer's model iP55-150 intensifier pump.

55,000 psi (3800 bar) Continuous Operating Pressure
150 hp, 3.2 gpm (12.1 lpm) Maximum Flow Rate

A CUT ABOVE

Experienced waterjet shops prefer Jet Edge hydraulic waterjet intensifier pumps.

Here’s why:

  • Reliable Tie-Rod Design eliminates threads on the high pressure cylinders, end caps, and hydraulic cylinders. This reduces the likelihood of cracking and increases component life.

  • Matched metal components prevent galling of hydraulic components. Intensifier designs allow for the usage of common tools instead of specialized jacking system tools. Hydraulic accumulators are standard on all pumps. This provides smoother hydraulic pressure, reduces spikes and prolongs hydraulic pump life.

  • Hydraulic fluid is cooled and filtered.

  • Rugged hydraulic center section incorporates high duty cycle-rated piston seal and wear rings.

  • Easy Maintenance - Access panels make it easy to maintain the pump. Intensifier components can be accessed without having to get into the hydraulic center section and hydraulic rod seal.

  • Leak detection block indicates seals needing replacement. (optional on some pumps).

  • No special tools required.

  • CE-marked attenuator smoothes pressure fluctuations and delivers constant and steady stream of UHP water.

  • On-board water filtration protects pump components, maximizing machine run time.

  • Standard Wye-Delta motor starter –Extends the life of the high-efficiency motor and minimizes installation costs.

  • Easy Operation - Jet Edge pumps can be controlled remotely from the motion controller and have programmable dual pressures.

PRODUCT SPECIFICATIONS
Construction
  • Heavy gauge sheet metal covers 
  • Rugged all-steel welded framework 
  • Hinged cover and removable access panels for convenient machine inspection and maintenance 
  • Integral hydraulic reservoir 
  • Sound insulated for quiet operation 
  • NEMA 12/13 rated electrical enclosure
Standard Features
  • High efficiency TEFC motor
  • 1,500 or 1,800 nominal motor speed (rpm)
  • Electronically shifted intensifiers
  • Wye-Delta soft start with disconnect
  • 0.5 gallon (1.9 liter) high pressure attenuator with 1.45 micron filtration
  • Safety shutdown systems
  • Automatic safety pressure bleed-down valve
  • Thermostatically controlled cooling system
  • Programmable Logic Controller (PLC) for operation and safety monitoring
  • Axial piston, variable displacement, pressure-compensated hydraulic pump
  • Liquid-filled pressure gauges
  • UHP safety shielded tubing

Optional Features

  • CE Mark
  • Advanced Controls
Low-Pressure Water/Intensification Water
  • Type: Pretreated, <100 TDS, PH 6-8, Silica <15PPM 
  • Supply Requirements: 2.9 gpm @ 20 psi (1.4 bar ) min. / 70°F (21°C) max
  • Filtration: 10, 1, .45 Micron
Coolant Water
  • Maximum Temperature: 70°F (21°C) 
  • Minimum: 5.2 gpm (19.6 lpm) @ Minimum 60 psi (4.1 bar)
  • Heat Exchanger: Stainless Steel Brazed Plate (1)
  • Heat Load: 105,000 BTU
Hydraulics
  • Reservoir Capacity: 103 gal (390 L)
  • Filtration: Kidney Loop 10 Micron 
Physical Size
  • Length: 83 in (2110 mm)
  • Width: 56 in (1430 mm)
  • Height: 56 in (1430 mm)
  • Approximate Weight with Fluid: 6800 lbs (3100 kg)
Electric Motor
  • Motor Output: 150 hp (112 kw)
  • Motor Type: High Efficiency TEFC electric motor
  • Full load amps @ 460vac: (60Hz) 177
  • Full load amps @ 230vac: (60Hz) 354
Intensifier
  • Type: Single piston, dual plunger, reciprocating
  • Number of Intensifiers: two
  • Continuous Operating Pressure: 55,000 psi (3800 bar)
  • Intensification Ratio: 19:1
  • Flow Rate: 3.2 gpm (12.1 lpm)
Environmental
  • Ambient Room Temperature: 50°-100°F (10°-37°C) 
  • Relative Humidity: Noncondensing, Maximum 95% @ 100°F
CUSTOM SOLUTIONS

Jet Edge is one of the few waterjet manufacturers willing to custom engineer solutions so you receive a system manufactured to satisfy your specific requirements. Our willingness to customize has made us the go-to waterjet supplier for solving the world’s toughest waterjet problems.

Call us today to discuss a custom solution for your manufacturing challenge!

1-800-JET-EDGE | 763-497-8700

LIFETIME TRAINING

Every Jet Edge system includes unlimited lifetime hands-on training at Jet Edge’s state-of-the art training lab. Training is free when taken at Jet Edge’s headquarters. You also can arrange to have training at your facility for a fee.

Register for classes online or call 1-800-JET-EDGE (538-3343) or +1 763-497-8700 to schedule custom training sessions for your business.

You must be a Jet Edge customer to be eligible for training.