iP36-80DS Diesel Waterjet Pump

36,000 psi (2500 bar) or 40,000 psi (2700 bar)
Continuous Operating Pressure, 80 hp
Maximum Flow Rate: 1.8 gpm (6.8 lpm) at 36,000 psi

A CUT ABOVE

Built with the waterjet contractor in mind, Jet Edge's diesel-powered waterjet intensifier pumps are built for years of dependable service in harsh and remote environments.

Experienced waterjet contractors prefer Jet Edge hydraulic waterjet intensifier pumps.

Here’s why:

  • Reliable Tie-Rod Design eliminates threads on the high pressure cylinders, end caps, and hydraulic cylinders. This reduces the likelihood of cracking and increases component life.

  • Reliable Cummins turbo diesel engines - Tier 3 certified.

  • Matched metal components prevent galling of hydraulic components. Intensifier designs allow for the usage of common tools instead of specialized jacking system tools. Hydraulic accumulators are standard on all pumps. This provides smoother hydraulic pressure, reduces spikes and prolongs hydraulic pump life.

  • Hydraulic fluid is cooled and filtered.

  • Rugged hydraulic center section incorporates high duty cycle-rated piston seal and wear rings.

  • Easy Maintenance - Intensifier components can be accessed without having to get into the hydraulic center section and hydraulic rod seal.

  • Leak detection block indicates seals needing replacement. (optional on some pumps).

  • No special tools required.

  • CE-marked attenuator smoothes pressure fluctuations and delivers constant and steady stream of UHP water.

  • On-board water filtration protects pump components, maximizing machine run time.

PRODUCT SPECIFICATIONS

Intensifier

  • Output Pressure: 36,000 psi (2500 bar) continuous
  • Number of intensifiers: 1 · 12:1 Intensification ratio
  • Flow rate: 1.8 gpm (6.8 L/m) at 36,000 psi or 1.6 gpm (6.05 L/m) at 40,000 psi
  •  

Engine

  • Engine output: 80 hp
  • Engine type: Cummins 4 cylinder turbocharged diesel (meets Tier 3 emission standard)
  • Fuel Tank: 27 U.S. gal (100 L)
  • Cooling: Air cooled circulating water (radiator)

Hydraulic

  • Pump type: Axial piston, variable displacement, pressure compensated
  • Pressure rating: 3,200 psi (220 bar)
  • Cooling: Air over oil heat exchanger
  • Filtration: 10 micron kidney loop; 13 gpm at 1800 rpm (49 L/m)
  • Fluid capacity: 35 U.S. gallons (135 L)
  • Fluid type: Standard: medium grade turbine ISO

Standard Features

  • A Programmable Logic Controller (PLC) operates the electronic timing of the intensifier cycle
  • 1.0 quart (0.9 liter) high pressure attenuator stabilizes operating pressure
  • Automatic safety pressure bleed-down valve relieves pressure from system
  • On-board Water Prefilter to 1 micron
  • Hydraulic accumulator dampens hydraulic fluid pulsations
  • Full flow hydraulic filtration to 10 micron increases hydraulic component life
  • Air cooled hydraulic fluid
  • Safety shutdown systems
  • Skid design

Optional CE Mark Available

Physical size

  • Length: 88 inches (2235 mm)
  • Width: 64 inches (1625 mm)
  • Height: 65 inches (1650 mm)
  • Weight: 3,500 lb (1590 kg) dry

Environmental

  • Ambient temperature: 50-100ºF (10-37º C)
  • Relative humidity: Non condensing, maximum 95% at 100ºF (37ºC)

Low Pressure Water

  • ·Type: Potable tap water

    *Pretreated, <100 TDS, PH 6-8, Silica <15PPM

  • Input Pressure: Minimum pressure 40 psi (3 bar) at 7 gpm (26 L/m)
  • Input temperature: Maximum temperature 70ºF (21ºC)
  • Filtration: Two filters, 10 micron and 1 micron

Specifications subject to change.

CUSTOM SOLUTIONS

Jet Edge is one of the few waterjet manufacturers willing to custom engineer solutions so you receive a system manufactured to satisfy your specific requirements. Our willingness to customize has made us the go-to waterjet supplier for solving the world’s toughest waterjet problems.

Call us today to discuss a custom solution for your manufacturing challenge!
1-800-JET-EDGE | 763-497-8700

LIFETIME TRAINING

Every Jet Edge system includes unlimited lifetime hands-on training at Jet Edge’s state-of-the art training lab. Training is free when taken at Jet Edge’s headquarters. You also can arrange to have training at your facility for a fee.

Register for classes online or call 1-800-JET-EDGE (538-3343) or +1 763-497-8700 to schedule custom training sessions for your business.

You must be a Jet Edge customer to be eligible for training.

Training for Jet Edge's mobile equipment line is being scheduled by request only. To request a class, please call 763-497-8700, Ext. 744