iP36-200 Waterjet Intensifier Pump

36,000 psi (2500 bar) Continuous Operating Pressure
200 hp, 6 gpm (22.7 lpm) Maximum Flow Rate

A CUT ABOVE

Experienced waterjet shops prefer Jet Edge hydraulic waterjet intensifier pumps.

Here’s why:

  • Reliable Tie-Rod Design eliminates threads on the high pressure cylinders, end caps, and hydraulic cylinders. This reduces the likelihood of cracking and increases component life.

  • Matched metal components prevent galling of hydraulic components. Intensifier designs allow for the usage of common tools instead of specialized jacking system tools. Hydraulic accumulators are standard on all pumps. This provides smoother hydraulic pressure, reduces spikes and prolongs hydraulic pump life.

  • Hydraulic fluid is cooled and filtered.

  • Rugged hydraulic center section incorporates high duty cycle-rated piston seal and wear rings.

  • Easy Maintenance - Access panels make it easy to maintain the pump. Intensifier components can be accessed without having to get into the hydraulic center section and hydraulic rod seal.

  • Leak detection block indicates seals needing replacement. (optional on some pumps).

  • No special tools required.

  • CE-marked attenuator smoothes pressure fluctuations and delivers constant and steady stream of UHP water.

  • On-board water filtration protects pump components, maximizing machine run time.

  • Standard Wye-Delta motor starter –Extends the life of the high-efficiency motor and minimizes installation costs.

  • Easy Operation - Jet Edge pumps can be controlled remotely from the motion controller and have programmable dual pressures.

PRODUCT SPECIFICATIONS
Physical Size
  • Length 95 in (2420 mm)
  • Width 60 in (1530 mm)
  • Height 60 in (1530 mm)
  • Approximate weight with fluid 6,200 lbs (2820 kg)
Electric Motor
  • Motor output 200 hp (149 kw)
  • Motor type High efficiency TEFC electric motor
  • Full load amps @ 460 VAC (60 Hz) 240
  • Full load amps @ 230 VAC (60 Hz) 480
  • Full load amps @ 380 VAC (50 Hz) 288
Intensifier
  • Type: Single piston, dual plunger, reciprocating
  • Number of intensifiers: 2
  • Continuous output pressure 36,000 psi (2500 bar)
  • Intensification ratio 12:1
  • Flow rate 6 gpm (22.7 liters per minute)
Low-Pressure Water
  • Type potable tap water *pretreated, <100 TDS, PH 6-8, Silica <15 PPM
  • Supply requirements 40 psi (2.75 bar) minimum, 70º F (21º C) maximum
  • Filtration: 1 micron
Coolant Water
  • Maximum temperature 70º F (21º C)
  • Minimum supply 5.7 gpm (21.61 lpm) at 60 psi (4.1 bar)
  • Heat Load: 125,000 BTU’s / HR
Hydraulics
  • Reservoir capacity 104 gallons (394 liters)
  • Filtration Full flow 10 micron
Environmental
  • Ambient room temperature 50°-100° F (10°-37° C)
  • Relative humidity: Noncondensing, maximum 95% at 100° F (37° C)
Sound Insulation
 
Optional CE Mark Available
 
Specifications subject to change.
CUSTOM SOLUTIONS

Jet Edge is one of the few waterjet manufacturers willing to custom engineer solutions so you receive a system manufactured to satisfy your specific requirements. Our willingness to customize has made us the go-to waterjet supplier for solving the world’s toughest waterjet problems.

Call us today to discuss a custom solution for your manufacturing challenge!

1-800-JET-EDGE | 763-497-8700

LIFETIME TRAINING

Every Jet Edge system includes unlimited lifetime hands-on training at Jet Edge’s state-of-the art training lab. Training is free when taken at Jet Edge’s headquarters. You also can arrange to have training at your facility for a fee.

Register for classes online or call 1-800-JET-EDGE (538-3343) or +1 763-497-8700 to schedule custom training sessions for your business.

You must be a Jet Edge customer to be eligible for training.